Thread Rating:
  • 5 Vote(s) - 3.8 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Clock Won't Update
#1
(1.9D Multispace) I've just replaced the radio (wouldn't eject CDs) with a spare one I had lying around and managed to figure out which wires to swap so the radio kept the memory. However the clock display only displays the time at which you switch the engine on. If you press the button to set the time the the time updates to the current time but then sits at that time until you press the button again.

Obviously it's related to me swapping over the radio and presumably there must be another wire which should be connected to a live feed or swapped over. Can anyone point me in the right direction please.
Malc

Stupid computer!
Security system should not fail safe!
Security system should fail dangerous!
Reply
#2
I've just realised that the part of the display that says whether the doors are still open is also not updating
Malc

Stupid computer!
Security system should not fail safe!
Security system should fail dangerous!
Reply
#3
Here's the wiring diagram. Make sure you have a constant 12v on pin 9 of the display (7215) and switched 12v on pin 7. Make sure you have a negative on pin 8. The constant 12v comes from fuse 4 in the Bsi. The switched supply is from fuse 14 in the Bsi. :thumbsup:

[Image: 20r8k7o.png]
2006 2.0hdi 600 with bench seat.  Cool
[-] The following 1 user says Thank You to Rustscrat for this post:
  • crickleymal
Reply
#4
Thanks, I'll have a look later and see what's happened. Odd that changing the radio caused this as I haven't changed the car wiring, Perhaps a wire is loose and fell out or something.
Malc

Stupid computer!
Security system should not fail safe!
Security system should fail dangerous!
Reply
#5
If everything looks ok, try a Bsi reset.Confusedalut:
2006 2.0hdi 600 with bench seat.  Cool
Reply
#6
Well that was odd. I checked the wiring and found I had permanent 12V on both 7 and 9. But to measure them I had to unplug the display. Plugged it back in and all seems to be ok. Thanks for the help though, it's always useful to have this info.
Malc

Stupid computer!
Security system should not fail safe!
Security system should fail dangerous!
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Welcome
You have to register before you can post on our site.

Username:
  

Password:
  




[-]
Search
(Advanced Search)

[-]
Latest Threads
Slow starter (diesel)
Last Post: zedhead
Today 10:09 AM
» Replies: 10
» Views: 217
ABS Modul
Last Post: highlander
Today 09:17 AM
» Replies: 0
» Views: 24
Type B MFD & Trip Computer
Last Post: cancunia
Today 08:55 AM
» Replies: 2
» Views: 76
Aftermarket radio stalk CTSCT003.2 Problem v2
Last Post: brajomobil
Today 07:39 AM
» Replies: 3
» Views: 112
jumps out in third gear..
Last Post: polar
Today 05:22 AM
» Replies: 7
» Views: 115
Fuel Guage wrong
Last Post: polar
Today 05:21 AM
» Replies: 1
» Views: 45
Wont start after dashboard removel
Last Post: joelfrodin
Yesterday 05:53 PM
» Replies: 10
» Views: 398
cold start
Last Post: geoff
Yesterday 05:23 PM
» Replies: 2
» Views: 80
Hello !
Last Post: geoff
Yesterday 09:52 AM
» Replies: 2
» Views: 63
Strut replacement- Spring Compression
Last Post: ffrenchie
Yesterday 09:15 AM
» Replies: 11
» Views: 439

[-]
Recent Visitors
Locations of visitors to this page