Thread Rating:
  • 9 Vote(s) - 2.44 Average
  • 1
  • 2
  • 3
  • 4
  • 5
XUD in Partner head gasket leak
#1
Hey all,

So i pulled the dw8 out of my partner and dropped in an xud td out of a zx . All was well untill yesterday when a big patch of oil appeared on the drive. further investigation seemed to suggest the cam shaft seal so i changed it last night. run it up and the leak is worse, a lot of head scratching and internet searches later i decided to rip her to bits thinking head gasket , the little o ring in the head gasket that seals the oil supply gallery to the head has perished and oil was pissing out of the side if the head at the back of the fuel injection pump. Other than the leak all was fine . The engine has 180k on it so well used.
Anyway my question is anyone out there got any ideas on some mods to make her go any better once shes back together , she was allready running 18psi boost and fuel and boost compensator turned up accordingly. I plan on replacing as much as possible within reason while shes in bits, head rebuild , sump off piston rings big end bearings and main bearings oil pump , all the gaskets and seals. Will probably replace the turbo as well whats good to go for in the turbo department. Anyone out there done owt like this before. Could do with some inspiration , and some time and money but will settle for the inspiration.
I have heard of these xud motors runnning 150bhp , that sounds a bit much but i might be wrong.
Thanks in advance.

Martin.......Confusedalut:
Reply
#2
Hello Mart,

Settle down with a cup of tea/couple of beers and have a look here:-

http://www.tdocuk.com/viewtopic.php?f=41&t=6702

and here:-

http://www.pug306.net/forum/forumdisplay...UD-section

You may need to register on the last one.
There are lots of other sites with various information, but these two will get you started.

Don't forget to keep us posted on what you're doing and remember - we like pictures !!!
[-] The following 1 user says Thank You to Coco for this post:
  • Mart7792
Reply
#3
(10-05-2012, 10:53 AM)Coco Wrote:  Hello Mart,

Settle down with a cup of tea/couple of beers and have a look here:-

http://www.tdocuk.com/viewtopic.php?f=41&t=6702

and here:-

http://www.pug306.net/forum/forumdisplay...UD-section

You may need to register on the last one.
There are lots of other sites with various information, but these two will get you started.

Don't forget to keep us posted on what you're doing and remember - we like pictures !!!

Thanks,

had several beers and found shed loads of great info, chomping at the bit to get started now. Oh and the usual dumb question how do u upload pictures.

thanks loads................ :drool:
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
[-]
Welcome
You have to register before you can post on our site.

Username:
  

Password:
  




[-]
Search
(Advanced Search)

[-]
Latest Threads
Speedo/milometer fault
Last Post: Gixxerguyk8
Today 12:28 AM
» Replies: 15
» Views: 1399
Which wheel nuts?
Last Post: Stu999
Yesterday 11:50 PM
» Replies: 0
» Views: 20
VAN SECURITY
Last Post: ricc
Yesterday 08:29 PM
» Replies: 5
» Views: 148
Clanking Brake Pedal Solved At Last!
Last Post: rickandbev16
Yesterday 06:53 PM
» Replies: 17
» Views: 3403
Head Light Bulbs
Last Post: dargoion
Yesterday 06:03 PM
» Replies: 31
» Views: 837
Good Evening to you all.
Last Post: Tomcat3
Yesterday 05:06 PM
» Replies: 6
» Views: 151
Are Mud Flaps the Answer ?
Last Post: polar
Yesterday 05:06 PM
» Replies: 3
» Views: 100
EGR solenoid
Last Post: silver-slug
Yesterday 02:46 PM
» Replies: 17
» Views: 1363
ABS Modul
Last Post: 3rensho
Yesterday 11:00 AM
» Replies: 1
» Views: 71
Slow starter (diesel)
Last Post: zedhead
Yesterday 10:09 AM
» Replies: 10
» Views: 240

[-]
Recent Visitors
Locations of visitors to this page