Thread Rating:
  • 7 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5
possible tire sizes 2007 van
There are 175/65/14 c Tires on the van.
I am wondering if it is possible to get a slightly bigger tire, something like 175/70/14C or 185/65/14 c fitted?
Any experiences?
Get a set of 185/65/15 on, transforms the handling and ride.
Somedays you're the pigeon, Somedays you're the statue.
what rim would that be?
Found on what car/van?
Found on berlingo multispace, various other citroens and peugeots
Somedays you're the pigeon, Somedays you're the statue.
I got the following tires: 175 / 70/ 14 reinforced Lasa, which are just that big higher to keep the van of the road. Drives great, - but have to mind the speedo.
the 15" rims I inspected at the breakers were all a different offset, so they would have interfered with the wheel housing in the back.
My 15 inch wheels on my 2006 Mk2 Partner are 6JH2 ET18. These are standard on the escapade version that has 40mm extra ground clearance.
The bigger wheels (185 65 15) account for about 11mm of this.
There isn't much clearance between the tyre and the coil spring and I think this will give me trouble when it comes time to use snow chains.

They are not that easy to come by,(picassos and 406 sometimes have the same size) and it might be easier to find a set of scrap alloys.

I'm contemplating a shift down to 14 inch steel rim with 175 70 14 tyres for the winter.

So far I haven't been able to confirm if this is a standard\allowable configuration on the high clearance escapade model.

Does your driver manual list allowable rim and tyre sizes?
I don't have an owners\drivers manual, but on other cars that I have owned, the manual did list the allowed rim configuration, e.g. standard steel rims, wide alloys, recommended winter tyres size and rim size etc.

on the MK1 and Mk2 the 14 inch rims are 5.5J with an offset of 23 or 24.

Both these and the 15inch wheels 6JH2 ET18 are listed in the pug workshop manual for use on the partner and partner van, so they should be ok for you.

I just can't find any information about my escaped high ground clearance version.

Oh yes, you will need the 4 stud with 108mm center distance. The hub hole diameter is 65mm or 65.1mm. I think mine are 65.1, but I did manage to squeeze on a set of 65mm without too much force\emmery paper!

Forum Jump:

Users browsing this thread: 1 Guest(s)
You have to register before you can post on our site.



(Advanced Search)

Latest Threads
Are Mud Flaps the Answer ?
Last Post: Solent
Today 12:28 PM
» Replies: 1
» Views: 18
ABS Modul
Last Post: 3rensho
Today 11:00 AM
» Replies: 1
» Views: 37
Slow starter (diesel)
Last Post: zedhead
Today 10:09 AM
» Replies: 10
» Views: 223
Type B MFD & Trip Computer
Last Post: cancunia
Today 08:55 AM
» Replies: 2
» Views: 78
Aftermarket radio stalk CTSCT003.2 Problem v2
Last Post: brajomobil
Today 07:39 AM
» Replies: 3
» Views: 115
jumps out in third gear..
Last Post: polar
Today 05:22 AM
» Replies: 7
» Views: 117
Fuel Guage wrong
Last Post: polar
Today 05:21 AM
» Replies: 1
» Views: 47
Wont start after dashboard removel
Last Post: joelfrodin
Yesterday 05:53 PM
» Replies: 10
» Views: 400
cold start
Last Post: geoff
Yesterday 05:23 PM
» Replies: 2
» Views: 82
Hello !
Last Post: geoff
Yesterday 09:52 AM
» Replies: 2
» Views: 63

Recent Visitors
Locations of visitors to this page