Posts: 77
Threads: 18
Thanks Received: 12 in 9 posts
Thanks Given: 8
Joined: Feb 2011
Location: south east kent
Reputation:
0
so the AA man said my glow plugs are the problem[starting] ,now ive got the manifold off i can replace the lower rocker gasket too
does it go on dry or a bit of sealant?
cheers steve
03 1.9DLX van
•
Posts: 47
Threads: 13
Thanks Received: 7 in 6 posts
Thanks Given: 0
Joined: Sep 2012
Location: United Kingdom
Reputation:
0
Guess what ive been doing for the last 1.5h?!
thats right redoing my rocker. I replaced mine with a new gasket about 2months ago, it was a massive pain to fit due to its shape, i got some advice about using superglue and/or silicon to hold it in place whilst you fit it but basically it was a pita!
Its been leaking a bit since i changed it over and really started making a mess this last week so ive been at it again. this time ive taken the gasket off and redone with silicon. just waiting for it to go off now. i hope its all sorted this time :brickwall:
•
Posts: 77
Threads: 18
Thanks Received: 12 in 9 posts
Thanks Given: 8
Joined: Feb 2011
Location: south east kent
Reputation:
0
27-02-2013, 07:23 PM
(This post was last modified: 27-02-2013, 07:27 PM by stevetiler.)
fair play mate, i fitted it today ,as u say it dont wanna play nice!!!!!!!!!!
in the end i tightened slightly the 3 bolts just enough to grip it as i tried to push it place,working my way round, its plenty thick aint!!
hopefully my plugs will be here tommorow so i can start it ,steve
p.s. im also gonna make a thin metal disc to blank the egr pipe,loads of crud in there......
03 1.9DLX van
•
Posts: 77
Threads: 18
Thanks Received: 12 in 9 posts
Thanks Given: 8
Joined: Feb 2011
Location: south east kent
Reputation:
0
what a crap design,this gasket keeps popping out and leakin like hell
any ideas?
03 1.9DLX van
•
Posts: 706
Threads: 32
Thanks Received: 157 in 129 posts
Thanks Given: 13
Joined: May 2011
Location: Ramsbottom
Reputation:
2
Have you tightened the bolts in sequence as per the haynes instructions and torqued them to the right setting?
If it doesn't sit very level it will push the gasket out where it's been over tightened.
•
Posts: 77
Threads: 18
Thanks Received: 12 in 9 posts
Thanks Given: 8
Joined: Feb 2011
Location: south east kent
Reputation:
0
havent got a manual mate or torque wrench
i started from the middle bit by bit
03 1.9DLX van
•
Posts: 706
Threads: 32
Thanks Received: 157 in 129 posts
Thanks Given: 13
Joined: May 2011
Location: Ramsbottom
Reputation:
2
I suspect it may be difficult that way.
There's a sequence in the Haynes that I used and it went back on right. I will have to check what order it says to use. Obviously the torque is quite important to have it sat flush with some consistency with the bolts.
If the gasket is popping out you are over tightening.
•
Posts: 77
Threads: 18
Thanks Received: 12 in 9 posts
Thanks Given: 8
Joined: Feb 2011
Location: south east kent
Reputation:
0
found a wrench mate if u got the info ,cheers steve
03 1.9DLX van
•
Posts: 77
Threads: 18
Thanks Received: 12 in 9 posts
Thanks Given: 8
Joined: Feb 2011
Location: south east kent
Reputation:
0
thanks very much mate ,ill give that a go
what i cant work out is the mating surfaces are flat but the seal has i raised ridge that looks like it should locate somewhere
03 1.9DLX van
•