Thread Rating:
  • 5 Vote(s) - 3.4 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[Brakes] Brake Pads for Berlingo B9 1.6
#1
Hi,

Looking to change the brake pads for a 2008 1.6 HDI Berlingo (the newer B9 model).  Can any one confirm the correct  part (I think it is Eurocarparts 101545708). 


Are there wear indicators on pads for the B9. Do I need any other tools (such as Torx bits) to change. 
Reply
#2
There two type's of brake pad's for the B9 one's with wear indicator's one's with out there are two way's to check look under the front of your berlingo to see if there is a wire fixed to the back of the pad's or go on line or ring them type in your reg or tell them it and they will tell the right one's 
                                     Smile  It's too orangey for crow's It's just for me and my dog  Smile

                                                        Heart Heart Love a lot trust a few  Dodgy
 
                                                        

                                        
Reply
#3
(04-10-2014, 11:21 AM)cascas Wrote:  Hi,

Looking to change the brake pads for a 2008 1.6 HDI Berlingo (the newer B9 model).  Can any one confirm the correct  part (I think it is Eurocarparts 101545708). 


Are there wear indicators on pads for the B9. Do I need any other tools (such as Torx bits) to change. 

Hi, if your vehicle is the same as my mark 3 van, you will need a large male torx bit (It was a female torx bit on the mark 2 Berlingo van); and a torque wrench capable of tightening these caliper bolts to 100nm. You don't mention your mileage, but I found that I had to fit new disks (a really simple job) roughly every 120,000 miles. Any half decent car parts depot should be able to give you the correct brake pads, if you give them your registration number. BTW, I've found parts bought from a Citroen main dealer quite competitive with other parts suppliers price-wise, and, often cheaper!
Reply
#4
Remember that you don't always need to change your discs when you changing your disc pads, therefore you don't need to remove the calliper carrier.
You need a 15mm and a 13mm combination spanner and some way of levering the pistons back
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Search Forums

(Advanced Search)

Latest Threads
increase in a ratchet-typ...
Last Post:saskak
Today 12:36 AM
» Replies: 7
» Views: 102
DW8 engine tapping
Last Post:Hector Scorn
Today 12:30 AM
» Replies: 0
» Views: 5
Rear Wiper Motor
Last Post:madwelshman
Yesterday 10:42 PM
» Replies: 3
» Views: 113
Heater control unit/resis...
Last Post:mreid63
Yesterday 10:34 PM
» Replies: 5
» Views: 336
Loud beeping from radio u...
Last Post:Tonyash
Yesterday 10:13 PM
» Replies: 0
» Views: 22
Facial light replacement
Last Post:Mike
Yesterday 09:23 PM
» Replies: 11
» Views: 288
Reverse light switch prob...
Last Post:willpisme
Yesterday 08:09 PM
» Replies: 7
» Views: 158
Rear hub nut torque setti...
Last Post:geoff
Yesterday 07:31 PM
» Replies: 4
» Views: 88
Heyup
Last Post:polar
Yesterday 07:18 PM
» Replies: 9
» Views: 373
New owner
Last Post:SheilaAnn
Yesterday 04:33 PM
» Replies: 12
» Views: 585

Locations of visitors to this page