Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[Brakes] 29 or 48 tooth ABS sensor
#1
Question 
Hi,

I have an ex-forestry Berlingo van. 2.0HDI my2006

as you can guess i have had to swap the rear axle. on pulling the old axle off it appears the previous owner has already swapped out the ABS equipped axle with a non-ABS axle.

so to confuse matters i now have a van that has ABS but the rear wheel bearings are non ABS.

I want to get the ABS functioning as it should so id like to find out is if i should buy the 29tooth wheel bearing or the 48 tooth wheel bearing?

Please help!
Reply
#2
I'd expect the front of the vehicle to use the same number of teeth as the rear so with this in mind you could count the number of teeth on the driveshaft reluctor ring to give you the answer.

You could of course ask at the main dealer spares counter and at the very least they could tell you which actual bearing you will need. A decent motor factors should also be able to assist.

Does your existing rear axle have the facility to mount the ABS sensors ? Sensors will also vary according to model / age.
Reply
#3
You get the ring built in with a new hub and bearing combined.
So where does this bit go then ?
Reply
#4
(11-10-2015, 10:44 PM)frogeyes Wrote:  Hi,

I have an ex-forestry Berlingo van. 2.0HDI my2006

as you can guess i have had to swap the rear axle. on pulling the old axle off it appears the previous owner has already swapped out the ABS equipped axle with a non-ABS axle.

so to confuse matters i now have a van that has ABS but the rear wheel bearings are non ABS.

I want to get the ABS functioning as it should so id like to find out is if i should buy the 29tooth wheel bearing or the 48 tooth wheel bearing?

Please help!


VIN of car to my PM
Reply
#5
(12-10-2015, 08:13 AM)geoff Wrote:  I'd expect the front of the vehicle to use the same number of teeth as the rear so with this in mind you could count the number of teeth on the driveshaft reluctor ring to give you the answer.

You could of course ask at the main dealer spares counter and at the very least they could tell you which actual bearing you will need. A decent motor factors should also be able to assist.

Does your existing rear axle have the facility to mount the ABS sensors ? Sensors will also vary according to model / age.

The axle does have space for sensors.

Will see if pk7478 can help.

Appreciate the replies so far
Reply
#6
In Vigo plant your M59 was equipped with 29 tooth wheel.
Model of sensor - Bosch 0 265 006 659
[+] 1 user says Thank You to pk7478 for this post
Reply
#7
Thank you so much!
Reply
#8
Well done PK !!!!!!!
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Search Forums

(Advanced Search)

Latest Threads
Bottom Ball joint
Last Post:Andyy
Today 08:06 PM
» Replies: 4
» Views: 44
peugeot charger
Last Post:geoff
Today 06:35 PM
» Replies: 4
» Views: 113
cutting out HDi 1.6 diese...
Last Post:Col
Today 06:15 PM
» Replies: 18
» Views: 1425
Poor cold startup 1.9
Last Post:Top drive
Today 06:10 PM
» Replies: 34
» Views: 789
hello
Last Post:ron
Today 05:22 PM
» Replies: 1
» Views: 32
Lower Ball Joint
Last Post:brodfather11
Today 03:36 PM
» Replies: 1
» Views: 47
starting problem
Last Post:brodfather11
Today 03:32 PM
» Replies: 1
» Views: 37
Washers not working
Last Post:Redjoe100
Today 03:25 PM
» Replies: 6
» Views: 140
citroen berlingo alarm
Last Post:sks01773
Today 11:28 AM
» Replies: 0
» Views: 33
Reverse light switch prob...
Last Post:ffrenchie
Today 09:48 AM
» Replies: 6
» Views: 107

Locations of visitors to this page