Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Torque on wheel nuts?
#1
It's time to switch to winter tires again... 
(Actually, it has been legal to do so here for over two weeks, but this morning was the first with frost and even a thin layer of ice on the road)

So, does anyone know how much to tighten the durn things?
(Mine's an old Mk. I with steel rims)
Reply
#2
According to Haynes its 90Nm or 66lbf ft. I always check them after 50 miles just to make sure their still tight.
Are we there yet????? No we fecking ain`t  gggggrrrrrrr
Ex 1.6hdi van now 3 seater 1.4 multispace
Reply
#3
As a rule of the thumb i always do mine - steel @ 100 ft lbs and alloy at 70 ft lbs.Whenever they are done for me which isnt very often but new tyre's etc the garages seem to set their air wrenches to max,i went to help an elderly chap back along only to find that after breaking 2 x wheel nut spanners i had to use a 3 feet piece of scaffolding on a breaker bar and i stood on the end and bounced before the nut came off and i'm 17 stone.!
Reply
#4
Tighten until they strip the thread then back off half-a-turn !!!!!  Rolleyes Rolleyes Rolleyes
Berlingo Multispace 2.0HDI '54 reg Mediterranean Blue
Reply
#5
I just go by feel, have spent so many years putting specified torque to fasteners and engines etc that I don't need a torque wrench. I even got tested for accuracy once for a £20 bet in work and the money went in my pocket.

The main thing to do is carry a breaker bar and correct socket to make sure you can undo the nuts when you get a puncture
Reply
#6
I agree with Tomcat3... I have alloys on my B9 and do the wheelnuts to 90Nm. I tighten the anti-theft "locking" nut on each wheel to a lower torque of 70Nm. This is because you can damage the pins on the special wheelnut "key" if you overtighten them.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Search Forums

(Advanced Search)

Latest Threads
peugeot charger
Last Post:Jed Clampit
Yesterday 11:28 PM
» Replies: 5
» Views: 133
hello
Last Post:Jed Clampit
Yesterday 11:16 PM
» Replies: 2
» Views: 44
XTR heater control bulb r...
Last Post:VicG
Yesterday 10:57 PM
» Replies: 0
» Views: 18
Fuel consumption
Last Post:ron
Yesterday 09:41 PM
» Replies: 12
» Views: 276
Rear Wiper Motor
Last Post:minisandfords
Yesterday 08:48 PM
» Replies: 2
» Views: 80
Lower Ball Joint
Last Post:brodfather11
Yesterday 08:38 PM
» Replies: 2
» Views: 73
Bottom Ball joint
Last Post:Andyy
Yesterday 08:26 PM
» Replies: 6
» Views: 84
cutting out HDi 1.6 diese...
Last Post:Col
Yesterday 06:15 PM
» Replies: 18
» Views: 1437
Poor cold startup 1.9
Last Post:Top drive
Yesterday 06:10 PM
» Replies: 34
» Views: 810
starting problem
Last Post:brodfather11
Yesterday 03:32 PM
» Replies: 1
» Views: 45

Locations of visitors to this page