Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[Brakes] Rear drum brake making squeaky noise
#1
How easy is it to strip rear drum brakes down, I've got a squeaky noise even when I remove the drum ever time I keep pulling hand brake up
Reply
#2
Easy .......... just take a photo of the parts layout so you don't forget how it all goes back - loads make a hash of remembering !!!!!!!
Reply
#3
I have the same problem right now, I kept greasing the shoe slots and reset the distance from the disk, but the noise comes back and I think it's because the adjust keeps moving. I got to find a way to stop it. Gets my handbrake higher after a month of driving. Don't really want to use loctite.

Here is some help buddy:
http://i.imgur.com/rLm4sAr.jpg
http://i.imgur.com/WCJfW7k.jpg
http://i.imgur.com/7xodTsF.jpg
Reply
#4
Mine does it ,but when its damp or been raining it stops??,,
Reply
#5
(30-09-2016, 09:58 PM)Kokain Wrote:  I have the same problem right now, I kept greasing the shoe slots and reset the distance from the disk, but the noise comes back and I think it's because the adjust keeps moving. I got to find a way to stop it. Gets my handbrake higher after a month of driving. Don't really want to use loctite.

Here is some help buddy:
http://i.imgur.com/rLm4sAr.jpg
http://i.imgur.com/WCJfW7k.jpg
http://i.imgur.com/7xodTsF.jpg

Looking at your photos, it looks as though you may have a weeping wheel cylinder due to the damp cruddy build up seen on the retaining springs. Shoes look unevenly worn too (thin in the centre)
I would replace shoes cylinders and drums. The adjusters won't be backing off, just not working. Clean them up and use ceramic grease on the threads.
Make sure the handbrake operating arm on the rear shoe is free to move and handbrake cable is extended enough for the arm to be in the fully rearward position as this is what adjusts the rear brakes. If the arm is slightly forward, back off the handbrake cable untill it is fully back. If the cable is too tight you will get the problems you describe.
Reply
#6
Something badly wrong there and has been for quite some time going by that much uneven shoe wear I'd be wanting to strip it all down to start again.

Also your handbrake cable doesn't look very healthy from the photograph and appears to be kinked and or chafed ?
Check it moves freely as a stiff cable can cause the adjustment to wander and action to be incorrect. Also it has been a while since I was doing brakes but does the cable run behind or in front of the shoe retaining plate ?
Reply
#7
(01-10-2016, 09:10 AM)geoff Wrote:  Also your handbrake cable doesn't look very healthy from the photograph and appears to be kinked and or chafed ?
Check it moves freely as a stiff cable can cause the adjustment to wander and action to be incorrect. Also it has been a while since I was doing brakes but does the cable run behind or in front of the shoe retaining plate ?

Good spot. That cable should be behind the plate.
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Search Forums

(Advanced Search)

Latest Threads
Door locking but unlocked
Last Post:ricc
Today 02:25 PM
» Replies: 4
» Views: 84
"Ultimate" type Diesel fu...
Last Post:ricc
Today 01:56 PM
» Replies: 18
» Views: 467
Heated wing mirrors
Last Post:Tree
Today 01:43 PM
» Replies: 5
» Views: 143
Ncb help
Last Post:ricc
Today 01:34 PM
» Replies: 6
» Views: 170
12v for lighter front
Last Post:ghost123uk
Today 01:07 PM
» Replies: 17
» Views: 351
Poor cold starting. Whats...
Last Post:Kez
Today 12:35 PM
» Replies: 0
» Views: 19
Repair a manual winder wi...
Last Post:AbneyTeal
Today 12:25 PM
» Replies: 0
» Views: 15
Fuel consumption
Last Post:Wyvern
Today 11:18 AM
» Replies: 6
» Views: 104
1.6 16v petrol cambelt
Last Post:sks01773
Today 10:56 AM
» Replies: 14
» Views: 327
lubricating door
Last Post:sks01773
Today 10:52 AM
» Replies: 3
» Views: 100

Locations of visitors to this page