Thread Rating:
  • 8 Vote(s) - 4.13 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Facia panel removal....anybody know how?
#1
Hi All,

It's that bit of facia with the window switches on and in particular the 'round blanks'. I would like to remove one of these and put in an additional cigar lighter socket for my satnav rather than trail the lead down to the fitted sockets. I obviously need to remove this small bit of facia but how?

I've lots of experience with classic cars but when it comes to the modern car and plastic I'm not so good. Any advice much appreciated.Confusedcratch:
Reply
#2
Hi, Is this any use?


.pdf   facia removal.pdf (Size: 245.72 KB / Downloads: 233)

Confusedalut:
2006 2.0hdi 600 with bench seat.  Cool
[+] 3 users say Thank You to Rustscrat for this post
Reply
#3
(09-06-2012, 01:10 PM)Rustscrat Wrote:  Hi, Is this any use?

Thankyou, That's a real helpConfusedalut:

So basically from what I can see, I just go straight to this small facia and prise it off? Do other folks agree with this and is there a trick....before I damage the plastic fixings?(something I'm quite good at! ConfusedillymeSmile



Confusedalut:
Reply
#4
yeah looks like it just pries out mate, use something softer than the trim piece so you dont damage it, or find a small sucker from something and try using that to dislodge it.
[+] 1 user says Thank You to Zion for this post
Reply
#5
(10-06-2012, 09:58 AM)Zion Wrote:  yeah looks like it just pries out mate, use something softer than the trim piece so you dont damage it, or find a small sucker from something and try using that to dislodge it.

Thankyou and I've done it! Put some gaffer tape around the perimeter of the facia and used several dinner knives to slide in(carefully avoiding the management indoors!). Eventually it came off but did damage one of the three lugs on the top but that doesn't show and hasn't affected the refitting.

Don't think it will take a cigar lighter though. Not a lot of room and there is only a small square hole at the back of the blanking.

Back to the drawing board.
Reply
#6
you may be able to fit the socket under the MFD tray. If you have the depth to take your ciggy socket then a hole saw could be used to make a neat fitting point for one. What about pulling another rubber capped one (like the 2nd one in the centre console) from a scrapper and fitting it there? Or take the lead down into the edge of the MFD tray and down behind the whole fascia, emerging in the clutter box at the bottom....then into the normal socket. Smile
[+] 1 user says Thank You to Zion for this post
Reply
#7
(10-06-2012, 12:12 PM)Zion Wrote:  you may be able to fit the socket under the MFD tray. If you have the depth to take your ciggy socket then a hole saw could be used to make a neat fitting point for one. What about pulling another rubber capped one (like the 2nd one in the centre console) from a scrapper and fitting it there? Or take the lead down into the edge of the MFD tray and down behind the whole fascia, emerging in the clutter box at the bottom....then into the normal socket. Smile

THANKYOU. MFD tray suggestion is favourite at the moment. I'm gonna think about it. Am I the only one who is irritated by the satnav trailing wire?
Reply
#8
nah mine annoys me too but I haven't decided where to fit it yet, I may end up putting the wire behind the fascia panels so no extra holes needed, just unclip the mfd tray and slacken the main fascia, then feed the power cable for the sat nav down the inside of the trim so it just appears from the edge of the mfd tray - file or cut a small notch in the edge so the tray sits ok. That way the 12v ciggy plug will lie in the crap tray at the bottom - hidden until needed.
[+] 1 user says Thank You to Zion for this post
Reply
#9
(10-06-2012, 01:22 PM)Zion Wrote:  nah mine annoys me too but I haven't decided where to fit it yet, I may end up putting the wire behind the fascia panels so no extra holes needed, just unclip the mfd tray and slacken the main fascia, then feed the power cable for the sat nav down the inside of the trim so it just appears from the edge of the mfd tray - file or cut a small notch in the edge so the tray sits ok. That way the 12v ciggy plug will lie in the crap tray at the bottom - hidden until needed.
Thanks ....that's given me an idea ! Cheers
Reply
#10
have to send this to be able to download the answer in the top
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Search Forums

(Advanced Search)

Latest Threads
peugeot charger
Last Post:Jed Clampit
Yesterday 11:28 PM
» Replies: 5
» Views: 132
hello
Last Post:Jed Clampit
Yesterday 11:16 PM
» Replies: 2
» Views: 42
XTR heater control bulb r...
Last Post:VicG
Yesterday 10:57 PM
» Replies: 0
» Views: 14
Fuel consumption
Last Post:ron
Yesterday 09:41 PM
» Replies: 12
» Views: 275
Rear Wiper Motor
Last Post:minisandfords
Yesterday 08:48 PM
» Replies: 2
» Views: 80
Lower Ball Joint
Last Post:brodfather11
Yesterday 08:38 PM
» Replies: 2
» Views: 69
Bottom Ball joint
Last Post:Andyy
Yesterday 08:26 PM
» Replies: 6
» Views: 81
cutting out HDi 1.6 diese...
Last Post:Col
Yesterday 06:15 PM
» Replies: 18
» Views: 1437
Poor cold startup 1.9
Last Post:Top drive
Yesterday 06:10 PM
» Replies: 34
» Views: 804
starting problem
Last Post:brodfather11
Yesterday 03:32 PM
» Replies: 1
» Views: 41

Locations of visitors to this page