Thread Rating:
  • 9 Vote(s) - 2.89 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Drive shaft removal
#1
Hi Folks,
Having fought my way past the mot it soon became obvious that that clutch was on the way. i watched a couple of youtube guides to clutch replacement, easy! but no idea of best way to remove drive shafts and in what order to remove suspension etc, think i need a ball joint removal tool only about £20 any advice about pitfalls greatly received.

thanks terry
[fon‌t=Arial]'If You're Not Living On The Edge, You're Taking Up Too Much Room.'
Founder Member: The Bad Parent Club!
[/font]
Reply
#2
(04-10-2012, 01:19 PM)terryd999 Wrote:  Hi Folks,
Having fought my way past the mot it soon became obvious that that clutch was on the way. i watched a couple of youtube guides to clutch replacement, easy! but no idea of best way to remove drive shafts and in what order to remove suspension etc, think i need a ball joint removal tool only about £20 any advice about pitfalls greatly received.

thanks terry

The drive shaft nut is 32mm or 36mm i am not sure which, but you will need either an air/electric impact gun or a 3' to 4' breaker bar and someone sitting in the car with the brakes on (M49 models with steel wheels it is possible to slacken the nut with the car on its wheels which makes things easier) also I have found when doing wheel bearings it is possible to remove the hub unit from the front suspension strut instead of removing the whole unit (pinch bolt at top of hub unit, use a steel wedge to spread it a gnat's and plenty of penetrant ) if you do not drain the gearbox oil first it dont half make a mess of the drive/garage floor Confusedillyme::whistle:
Reply
#3
(09-10-2012, 12:16 PM)Husqyman Wrote:  
(04-10-2012, 01:19 PM)terryd999 Wrote:  Hi Folks,
Having fought my way past the mot it soon became obvious that that clutch was on the way. i watched a couple of youtube guides to clutch replacement, easy! but no idea of best way to remove drive shafts and in what order to remove suspension etc, think i need a ball joint removal tool only about £20 any advice about pitfalls greatly received.

thanks terry

The drive shaft nut is 32mm or 36mm i am not sure which, but you will need either an air/electric impact gun or a 3' to 4' breaker bar and someone sitting in the car with the brakes on (M49 models with steel wheels it is possible to slacken the nut with the car on its wheels which makes things easier) also I have found when doing wheel bearings it is possible to remove the hub unit from the front suspension strut instead of removing the whole unit (pinch bolt at top of hub unit, use a steel wedge to spread it a gnat's and plenty of penetrant ) if you do not drain the gearbox oil first it dont half make a mess of the drive/garage floor Confusedillyme::whistle:

Thanks Husqyman
for the tips about removing the hubs, unfortunately i already found out about gearbox oil when i replaced rubber bush on suspension arm and removed calipers for new brake discs, pulled out driveshaft without realising and then went for bacon sarni break,
Easy to refill through the top breather under battery tray till it runs out of 22mm drain plug under n/s wheel arch, behind plastic arch liner.
Getting quite familiar with suspension now, changed o/s front wheel bearing recently. relatively simply apart from fitting actual bearing into hub, was told after much struggle that garages use a 20 tonne press to push bearing in to hub.so best left to people with right tools.
I hope this info helps someone else. but personally i always like to learn the hardest way, it's character building!!!!!!
[fon‌t=Arial]'If You're Not Living On The Edge, You're Taking Up Too Much Room.'
Founder Member: The Bad Parent Club!
[/font]
Reply
#4
Hi, This any use? Confusedalut:

http://www.berlingoforum.co.uk/attachment.php?aid=624
2006 2.0hdi 600 with bench seat.  Cool
Reply
#5
(09-10-2012, 09:34 PM)Rustscrat Wrote:  Hi, This any use? Confusedalut:

http://www.berlingoforum.co.uk/attachment.php?aid=624
Hi Rustscrat.
Thanks for most excellent information. i will get a ball joint tool and then i think i can tackle the rest to remove driveshafts and replace the clutch,
Lets hope so anyway, cant afford to pay local trusted garage £490 and tried Mr Clutch, they quoted £269.99 seems too cheap when 2 sources said about 6 hours labour. What do you think? thanks again. Terry
[fon‌t=Arial]'If You're Not Living On The Edge, You're Taking Up Too Much Room.'
Founder Member: The Bad Parent Club!
[/font]
Reply
#6
(09-10-2012, 10:12 PM)terryd999 Wrote:  
(09-10-2012, 09:34 PM)Rustscrat Wrote:  Hi, This any use? Confusedalut:

http://www.berlingoforum.co.uk/attachment.php?aid=624
Hi Rustscrat.
Thanks for most excellent information. i will get a ball joint tool and then i think i can tackle the rest to remove driveshafts and replace the clutch,
Lets hope so anyway, cant afford to pay local trusted garage £490 and tried Mr Clutch, they quoted £269.99 seems too cheap when 2 sources said about 6 hours labour. What do you think? thanks again. Terry
Have read bad things on the forum about Mr clutch Confusedtudy:
2006 2.0hdi 600 with bench seat.  Cool
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Search Forums

(Advanced Search)

Latest Threads
12v for lighter front
Last Post:ghost123uk
Today 02:59 PM
» Replies: 6
» Views: 135
Insurance!
Last Post:Col
Today 02:57 PM
» Replies: 9
» Views: 873
"Ultimate" type Diesel fu...
Last Post:ghost123uk
Today 02:48 PM
» Replies: 17
» Views: 400
2025 Diesel Ban
Last Post:rnamman
Today 01:58 PM
» Replies: 9
» Views: 135
2012 enterprise berlingo ...
Last Post:Solent
Today 01:47 PM
» Replies: 8
» Views: 169
Alloys
Last Post:Rich Walker
Today 01:36 PM
» Replies: 3
» Views: 116
1.6 16v petrol cambelt
Last Post:sks01773
Today 09:28 AM
» Replies: 4
» Views: 72
citroen berlingo desire 1...
Last Post:Trevor
Today 09:18 AM
» Replies: 3
» Views: 79
Berlingo won't start 2009...
Last Post:brodfather11
Today 06:20 AM
» Replies: 8
» Views: 212
B9 DPF Tank Top-Up
Last Post:Lighty
Yesterday 10:06 PM
» Replies: 5
» Views: 130

Locations of visitors to this page