Thread Rating:
  • 5 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Clutch Pedal Travel
#1
Replaced the leaking clutch slave cylinder today.
Easy job.
Not so easy to bleed the system!
Took 2 hrs and now I have a problem. Confusedcratch:
If the clutch pedal has 6 inches of travel (for example), I now have 4 inches of nothing (no resistance) and 2 inches of resistance with the bite right at the bottom. The clutch works (just about), but it is obviously not right.
Where have I gone wrong?
The clutch was fine before.
Reply
#2
Sounds like you still have a lot of air in the system to me. Brakes that arent fully bled exhibit the symptoms you describe.
[+] 1 user says Thank You to FeuxLingo for this post
Reply
#3
That's what I thought.
But bled and bled till no air visible. Then bled again. And again.
Took ages to get any pedal at all (and pedal wouldn't even return to the top without manually pulling it), just went straight to the floor.
Reply
#4
(03-11-2012, 09:33 PM)j90xxx Wrote:  That's what I thought.
But bled and bled till no air visible. Then bled again. And again.
Took ages to get any pedal at all (and pedal wouldn't even return to the top without manually pulling it), just went straight to the floor.

Unless you have a leak, or there's something wrong with the clutch master cylinder (internal leak), then it can only be air in the system.
[+] 1 user says Thank You to FeuxLingo for this post
Reply
#5
Has the slave cylinder been fitted with the bleed nipple higher than the fluid pipe, I don't know if it is possible to fit it 180 degrees out, but it does sound like air in the system and if the bleed nipple was below the pipe it might allow air to be trapped in the cylinder.
Assuming that the clutch worked OK other than leaking fluid prior to the swap then your problem has got to be something that has just been changed.
If you had similar symptoms prior to the swap than you could have problems with the clutch release arm or release bearing inside the bellhousing. I'm new to Citroens, but used to have a Land Rover that had the £10 clutch arm fail on two occasions. (engine or gearbox out)
Have you been losing clutch fluid or is there some other reason that you have diagnosed a knackered slave cylinder.
Reply
#6
If you can restrict the movement of the slave piston,open & close the nipple at each pump,it should clear the air.With the piston held back creating a smaller space behind it,you get a better "scouring" effect making the fluid travel faster & taking the air with it.
Strawberry flavoured windows  Dodgy
Reply
#7
It was air Confusedillyme: , a lot of it!
The tiny rubber seal on the end of the hydraulic pipe where it enters the slave cylinder wasn't seated correctly, so was drawing fluid AND air.
Sometimes the simplest things catch you out? Confusedillyme:
Refitted and bled the system. It appears to be working fine now.
Thanks everyone for your replies. :thumbsup:
[+] 1 user says Thank You to j90xxx for this post
Reply
#8
Fitters, I've s*it 'em !!!!

Glad you've sorted though Martin...
Berlingo Multispace 2.0HDI '54 reg Mediterranean Blue
[+] 2 users say Thank You to andy-womble for this post
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Search Forums

(Advanced Search)

Latest Threads
DW8 engine tapping
Last Post:jj9
Today 01:14 AM
» Replies: 3
» Views: 91
Rear window heater repair
Last Post:Silverberlingo
Yesterday 11:38 PM
» Replies: 0
» Views: 25
New PureTech 110 S&S Flai...
Last Post:Jed Clampit
Yesterday 09:04 PM
» Replies: 3
» Views: 57
What website to pass time...
Last Post:Solent
Yesterday 08:32 PM
» Replies: 0
» Views: 32
Berlingo Parts
Last Post:Sb12
Yesterday 07:56 PM
» Replies: 0
» Views: 34
Rear hub nut torque setti...
Last Post:jj9
Yesterday 07:55 PM
» Replies: 15
» Views: 261
temperatue dial
Last Post:Kokain
Yesterday 05:28 PM
» Replies: 3
» Views: 76
Trip Computer on Type A M...
Last Post:cancunia
Yesterday 03:50 PM
» Replies: 0
» Views: 25
Loud beeping from radio u...
Last Post:nicko
Yesterday 03:49 PM
» Replies: 3
» Views: 116
Ligts won't go off!
Last Post:Berlingos12
Yesterday 02:50 PM
» Replies: 10
» Views: 470

Locations of visitors to this page