Thread Rating:
  • 6 Vote(s) - 1.83 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Removal of tray between front seats
#1
Can anyone give guidance about removing the central tray, I have lifted the felt pad to find a couple of hex head screws and a nut inside a deep recess, this seems straightforward. The anticipated problem is that the handbrake is surrounded by an integrated rigid plastic moulding ....... this is the problem, any suggestions about removing this handbrake moulding?
Thanks in anticipation
Reply
#2
From a quick look at my enterprise van (the bench-seat arrangement) the moulding is in two halves either side of the lever.
Try to lever them apart in an inconspicuous area and be prepared for broken clips.
Find out how much a new one is first!

What are you up to? - or shouldn't I be asking....
Reply
#3
(05-11-2012, 05:08 PM)evdama Wrote:  From a quick look at my enterprise van (the bench-seat arrangement) the moulding is in two halves either side of the lever.
Try to lever them apart in an inconspicuous area and be prepared for broken clips.
Find out how much a new one is first!

What are you up to? - or shouldn't I be asking....

No problem in asking, hope to fit a 12volt socket, maybe the mini socket type depending on room, which will be wired to a constant live feed through a fused spur. Hopefully this will be a neat job.
Reply
#4
U can take the plastic of the handbrake just pry it with a flat head screw driver done it my self a while ago pretty simple
Reply
#5
Is yours a two piece or one piece moulding. if its a two piece then there should be four torx screws that you need to remove, after that your pull back the rear piece and lower the handbrake slightly to remove. refitting is the reverse procedure if my memory serves me well. But you shouldn't have much problems just remember to park on level ground and chock the wheels for safety.

don't touch the nut as this is the handbrake tensioner
Reply
#6
i used this when i was changing my cigar lighter, was very useful.


Attached Files
.zip   ere.zip (Size: 86.95 KB / Downloads: 26)
Reply
#7
hi. you also might have to release handbrake cable to give you more flexibility,...........cheers..............[Image: smile.png]
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Search Forums

(Advanced Search)

Latest Threads
Repair a manual winder wi...
Last Post:AbneyTeal
Today 12:25 PM
» Replies: 0
» Views: 2
Fuel consumption
Last Post:Wyvern
Today 11:18 AM
» Replies: 6
» Views: 92
12v for lighter front
Last Post:nicko
Today 11:09 AM
» Replies: 16
» Views: 340
1.6 16v petrol cambelt
Last Post:sks01773
Today 10:56 AM
» Replies: 14
» Views: 324
lubricating door
Last Post:sks01773
Today 10:52 AM
» Replies: 3
» Views: 97
how many miles on yours ?
Last Post:Wyvern
Today 10:27 AM
» Replies: 18
» Views: 814
Roof noise
Last Post:Opensauce
Today 09:59 AM
» Replies: 2
» Views: 70
Rear light Cluster
Last Post:Opensauce
Today 09:50 AM
» Replies: 3
» Views: 93
Saying Hello
Last Post:ghost123uk
Today 09:07 AM
» Replies: 2
» Views: 48
Lexia clone that works wi...
Last Post:brajomobil
Today 08:02 AM
» Replies: 59
» Views: 1863

Locations of visitors to this page