Thread Rating:
  • 11 Vote(s) - 2.27 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[Engine] Cold Start Adjustment
#1
I'm trying to get the cold start on my 1.9 DW8 working properly. It was adjusted so that the engine was running at 1100 rpm. The knurled cable adjuster is pretty much rusted up tight and when I try to turn it the bracket starts to bend. I slackened off the nipple and put some slack into the cable. Now the cold start doesn't seemto work. It starts and idles at about 750 rpm picking up to 800 when the engine is warm.

How much slack shoud be in the cable and where does it go to? What is at the other end of the cable to pull it to make the cold start work?

Thanks
Malc

Stupid computer!
Security system should not fail safe!
Security system should fail dangerous!
Reply
#2
When the engine is cold there shoud not be any slack. When it warms up the thermostatic sensor located in the cooling system expands, the cable slackens and reduces the idle speed. My (xud) sensor is located in the thermostat housing. I think ? that yours (dw) is either in the fuel filter housing or the thermostat area. It dosen't seem to be working, try adjusting it when cold. They can be replaced.

Confusedtudy:
[+] 1 user says Thank You to brodfather11 for this post
Reply
#3
Thanks. The cable was tight at all times before I fiddled and the idle speed never varied from 1100rpm.
Malc

Stupid computer!
Security system should not fail safe!
Security system should fail dangerous!
Reply
#4
So I managed to unfreeze the cable adjustment and adjusted it when the engine was just about cold for 1100rpm. The today (it's quite cold) I start the engine and it idles at 800 rpm. When I get to work 35 miles later it's idling at 1100 rpm. So the bloody thing is working backwards. Help!!

Does anyone know of a Citroen/Peugeot specialist in Gloucester?
Malc

Stupid computer!
Security system should not fail safe!
Security system should fail dangerous!
Reply
#5
This any use Mal ??


.pdf   Injection pump adjustment.pdf (Size: 43.61 KB / Downloads: 79)

Confusedalut:
2006 2.0hdi 600 with bench seat.  Cool
[+] 3 users say Thank You to Rustscrat for this post
Reply
#6
That's great. Thanks very much
Malc

Stupid computer!
Security system should not fail safe!
Security system should fail dangerous!
Reply
#7
This must be a fairly common failure. I got the cold start mechanism out of a scrapped Berlingo and it doesn't move either. I stuck the temperature sensor in hot water for 10 minutes and the cable didn't move. Then I stuck it in the freezer for half an hour and it still didn't move.
Does anyone know the part number so I can order a new one please?
Malc

Stupid computer!
Security system should not fail safe!
Security system should fail dangerous!
Reply
#8
Not a problem for the part Number Malc, if you could PM me your Vin No. I can get an accurate match. :thumbsup:
2006 2.0hdi 600 with bench seat.  Cool
Reply
#9
You have a PM.
Malc

Stupid computer!
Security system should not fail safe!
Security system should fail dangerous!
Reply
#10
I've just seen the cost of one on Ebay. Feckity, feckity, feck £235!!!!. No wonder they don't get repaired. Maybe I'll fit a choke cable.
Malc

Stupid computer!
Security system should not fail safe!
Security system should fail dangerous!
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Search Forums

(Advanced Search)

Latest Threads
Rear hub nut torque setti...
Last Post:El Berlingo
Today 01:14 PM
» Replies: 3
» Views: 39
Poor cold startup 1.9
Last Post:jj9
Today 09:42 AM
» Replies: 35
» Views: 842
peugeot charger
Last Post:Jed Clampit
Yesterday 11:28 PM
» Replies: 5
» Views: 164
hello
Last Post:Jed Clampit
Yesterday 11:16 PM
» Replies: 2
» Views: 56
XTR heater control bulb r...
Last Post:VicG
Yesterday 10:57 PM
» Replies: 0
» Views: 40
Fuel consumption
Last Post:ron
Yesterday 09:41 PM
» Replies: 12
» Views: 307
Rear Wiper Motor
Last Post:minisandfords
Yesterday 08:48 PM
» Replies: 2
» Views: 96
Lower Ball Joint
Last Post:brodfather11
Yesterday 08:38 PM
» Replies: 2
» Views: 102
Bottom Ball joint
Last Post:Andyy
Yesterday 08:26 PM
» Replies: 6
» Views: 117
cutting out HDi 1.6 diese...
Last Post:Col
Yesterday 06:15 PM
» Replies: 18
» Views: 1479

Locations of visitors to this page