Thread Rating:
  • 5 Vote(s) - 4.2 Average
  • 1
  • 2
  • 3
  • 4
  • 5
light burning smell coming from heater
#1
Lads,

getting a light burning smell out of the air vents when the heater is on.

Any ideas what up?
Reply
#2
Usually it's the blower fan motor, either the controller circuit board warming up excessively or the brushes arcing due to wear/loss of spring pressure.
Reply
#3
Check this link out, that smell could be the coolant evaporating off too.
http://www.berlingoforum.co.uk/showthread.php?tid=359
Reply
#4
Matrix replacement sounds like a big job. would it be worth having a look at addo idea first?
Reply
#5
Coolant leaking and evaporating usually smells like curry, well it does to me Big Grin
So where does this bit go then ?
Reply
#6
When my Xantia's current matrix was brand new it gave off a light burning smell, I'd scrubbed the heater box out so there was no coolant residue.
Reply
#7
I think addo is probably more knowledgeable than I am so yes I would try his thing first. I just wanted to draw your attention to that possibility. I had that (curry?) smell for a while but decided to ignore it and see what happened, either it has now gone or I dont notice it any more. I seem to remember my old xsara had it too now and then. If it is a real electrical burning smell I think addo is probably right.
[+] 1 user says Thank You to mrbritse for this post
Reply
#8
I wouldn't so much say knowledge; it's more about burned/bruised/scraped fingertips from poking and prodding things that make me curious! :whistle:

My Xantia's blower control module fritzed out several times, in the end I determined the brushes were half worn away - you'd think it should still work fine, but in reality it was lacking the spring pressure to transmit enough current consistently - so it would slow, then the controller module would say "more speed" and it would speed up again with resultant slight arcing and ionising smell. The fast/slow muddle overheated the controller and scorched its circuit board, causing the tracks to become unbonded from its base material.

See how it goes for smell, with the fan speed set to a constant speed rather than automatic climatisation. If the burning smell can be mitigated this way, I suggest re-brushing your motor (about ten squid and an afternoon for the halfway handy). Brushes are likely to have been 22mm long when new - less than ten mil left and they're going to be problematic from my observations.

Re the matrix - try Forté before ripping the dash out.
[+] 2 users say Thank You to addo for this post
Reply
#9
would any one have a diagram for this / work instruction .Ill replace the bushing first and see if the smell goes
Reply
#10
(29-01-2013, 12:00 PM)addo Wrote:  I wouldn't so much say knowledge; it's more about burned/bruised/scraped fingertips from poking and prodding things that make me curious! :whistle:

My Xantia's blower control module fritzed out several times, in the end I determined the brushes were half worn away - you'd think it should still work fine, but in reality it was lacking the spring pressure to transmit enough current consistently - so it would slow, then the controller module would say "more speed" and it would speed up again with resultant slight arcing and ionising smell. The fast/slow muddle overheated the controller and scorched its circuit board, causing the tracks to become unbonded from its base material.

See how it goes for smell, with the fan speed set to a constant speed rather than automatic climatisation. If the burning smell can be mitigated this way, I suggest re-brushing your motor (about ten squid and an afternoon for the halfway handy). Brushes are likely to have been 22mm long when new - less than ten mil left and they're going to be problematic from my observations.

Re the matrix - try Forté before ripping the dash out.

What's Forte and what does it do. As I have the sweet smell of coolant evaporting when the heater is on
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Search Forums

(Advanced Search)

Latest Threads
Rear light Cluster
Last Post:Peter Guy
Today 08:01 PM
» Replies: 5
» Views: 110
1.6 16v petrol cambelt
Last Post:sks01773
Today 07:27 PM
» Replies: 16
» Views: 359
Poor cold starting. Whats...
Last Post:Top drive
Today 07:02 PM
» Replies: 6
» Views: 74
Roof noise
Last Post:Opensauce
Today 06:39 PM
» Replies: 5
» Views: 110
12v for lighter front
Last Post:Matija Danko
Today 05:15 PM
» Replies: 19
» Views: 390
Fuel consumption
Last Post:ron
Today 04:30 PM
» Replies: 7
» Views: 133
Lexia clone that works wi...
Last Post:kennard
Today 04:22 PM
» Replies: 60
» Views: 1900
Repair a manual winder wi...
Last Post:cancunia
Today 03:31 PM
» Replies: 1
» Views: 35
lubricating door
Last Post:cancunia
Today 03:25 PM
» Replies: 4
» Views: 119
Door locking but unlocked
Last Post:ricc
Today 02:25 PM
» Replies: 4
» Views: 91

Locations of visitors to this page