Thread Rating:
  • 13 Vote(s) - 3.69 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Key fob programming help
#1
I've recently bought a spare key for an '05 multispace but the remote central locking doesn't work with it.

I've read around and there's a few guides on how to program it to work but no matter what I try the new key just won't bind. All instructions I've found say you need to repeat the steps for each fob but I've deliberately not done the steps for the old fob and it still works so I'm guessing it's not even going into programming mode.

Any ideas on exactly what the correct procedure should be? Or can this only be done with a lexia 3?
Reply
#2
Have a read of this. Confusedtudy: Confusedalut:

.pdf   key fob syncing2.pdf (Size: 12.65 KB / Downloads: 386)
2006 2.0hdi 600 with bench seat.  Cool
[+] 3 users say Thank You to Rustscrat for this post
Reply
#3
Thanks for this post.
Reply
#4
let's try
Reply
#5
My remote key didn't seem to work, when I opened it up the microswitch had come off. New one bought for £1.50 and soldered on in seconds and all working properly now!!
Reply
#6
(19-10-2013, 08:46 PM)Waynejohnson Wrote:  My remote key didn't seem to work, when I opened it up the microswitch had come off. New one bought for £1.50 and soldered on in seconds and all working properly now!!

Which microswitch was that?
[fon‌t=Tahoma, Calibri, Verdana, Geneva, sans-serif]The Older I get the Better I Was!  Cool [/font]
Reply
#7
Similar (I think) problem for me. New key fob, put existing transponder inside, remote lock/unlock works but engine won't start. Hopefully now I've posted I can download the above instructions...

Wink
Reply
#8
Thectransponder is probably too far away from the sensor.

Have you tried removing transponder placing next to sensor and then trying to start the car,?
Reply
#9
Fixed - problem mainly due to me being an idiot. I'd transferred a new key to the new fob, plus the original circuit board. What I hadn't swapped was the little black transponder from the corner. Once I swapped that too everything then worked.

Ta for the advice though!
Reply
#10
Hi sorry to drag up an old post but i need to post a reply to download the document, i recently bought a second hand key fob from ebay for my berlingo, i swapped the back over and it starts but cant get the fob to program to the car, the circuit board inside does look different to the old one, will the different type still be compatible?
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Search Forums

(Advanced Search)

Latest Threads
Poor cold startup 1.9
Last Post:jj9
Yesterday 11:57 PM
» Replies: 39
» Views: 1050
2004 Berlino Aerial
Last Post:brodfather11
Yesterday 10:48 PM
» Replies: 1
» Views: 29
Washers not working
Last Post:Lighty
Yesterday 09:09 PM
» Replies: 11
» Views: 301
Reverse light switch prob...
Last Post:Col
Yesterday 07:22 PM
» Replies: 12
» Views: 254
2005 2.0 HDI Siemens pump...
Last Post:Woodyrvf750
Yesterday 07:05 PM
» Replies: 0
» Views: 28
Fuse is burning all the t...
Last Post:fernandoblas
Yesterday 05:23 PM
» Replies: 12
» Views: 415
HELP! Smashed passenger w...
Last Post:Sootyfoot
Yesterday 04:31 PM
» Replies: 2
» Views: 71
Diagnostic "gear" / Softw...
Last Post:cancunia
Yesterday 04:19 PM
» Replies: 15
» Views: 619
Berlingo Parts
Last Post:malgpz900
Yesterday 10:20 AM
» Replies: 1
» Views: 90
XTR heater control bulb r...
Last Post:Opensauce
Yesterday 09:19 AM
» Replies: 1
» Views: 85

Locations of visitors to this page