Thread Rating:
  • 4 Vote(s) - 2 Average
  • 1
  • 2
  • 3
  • 4
  • 5
ignition problem
#1
my mark 1 berlingo cut out on me this afternoon, and wouldnt re-start.now when you attempt to start, the alarm sounds, and alarm icon appears on the dashboard. on further inspection it had blown a fuse, but when this fuse is replaced, it simply blows again, and the vehicle refuses to start, anyone any idea as to what the problem could be?
Reply
#2
If you could let us know which fuse in which fuse box it might help us to find your problem. petrol or diesel?
Reply
#3
its a 20 amp fuse, halfway down fusebox on the right , underneath the sterring wheel, sorry i cant be more specific, as casing is missing-must be related to ignition, as when this is replaced, engine starts for a short while, then blows it again
Reply
#4
You're too vague for me, there are some twenty amp fuses on mine but they are all in numbered positions in the fuse box and I dont have an alarm system. If you wait either Rustscarts or addo will no doubt be along soon and they will know which fuse you mean. It would help if you say what engine is in it and what model , ie air conditioning, rear wipers or what , etc

:thumbsup: Confusedcratch:
Reply
#5
It's a big difference between mux and non-mux cars. What is the RPO (five digit number on the door jamb sticker)?
Reply
#6
(04-02-2013, 09:40 PM)brodfather11 Wrote:  You're too vague for me, there are some twenty amp fuses on mine but they are all in numbered positions in the fuse box and I dont have an alarm system. If you wait either Rustscarts or addo will no doubt be along soon and they will know which fuse you mean. It would help if you say what engine is in it and what model , ie air conditioning, rear wipers or what , etc

:thumbsup: Confusedcratch:

vehicle is a t(99 reg) diesel, non air con-will post rpo number later, thanks for your help
Reply
#7
update on ignition problem, car started ok this morning with fuse replaced, and ran for 3 miles with no problems, went through some deep water yesterday so maybe it was causing fusing problem! when ignition switch is turned off, there are 3 double beeps, does anyone know if this is a fault code? again, many thanks for all your help
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Search Forums

(Advanced Search)

Latest Threads
Fuel consumption
Last Post:ron
Today 09:41 PM
» Replies: 12
» Views: 260
Rear Wiper Motor
Last Post:minisandfords
Today 08:48 PM
» Replies: 2
» Views: 76
Lower Ball Joint
Last Post:brodfather11
Today 08:38 PM
» Replies: 2
» Views: 62
Bottom Ball joint
Last Post:Andyy
Today 08:26 PM
» Replies: 6
» Views: 73
peugeot charger
Last Post:geoff
Today 06:35 PM
» Replies: 4
» Views: 117
cutting out HDi 1.6 diese...
Last Post:Col
Today 06:15 PM
» Replies: 18
» Views: 1429
Poor cold startup 1.9
Last Post:Top drive
Today 06:10 PM
» Replies: 34
» Views: 793
hello
Last Post:ron
Today 05:22 PM
» Replies: 1
» Views: 33
starting problem
Last Post:brodfather11
Today 03:32 PM
» Replies: 1
» Views: 39
Washers not working
Last Post:Redjoe100
Today 03:25 PM
» Replies: 6
» Views: 144

Locations of visitors to this page