Thread Rating:
  • 8 Vote(s) - 2.88 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Berlingo IBS and ECU Units
#1
Thanks in advance - I bought the van, a 2003 1.9D (think it's a MK11 - large headlights) from my neighbour. He had bought it on line and was told it had a lighting fault. Problems start when starting from cold - engine fires up but sounds diesel knock for a few minutes. Then sounds sweet. Headlight flash works, sidelights work but no headlights when stalk is turned on. Then fuel gauge will fall to zero, handbrake warning light and charge light stop on. No rev counter, engine light comes and goes after about 10 mins when temp gauge goes up headlights start working.
Also wipers, rev counter work and charge light goes off. Drives ok for a bit then diesel knock comes back on and off with loss of power - like timing retarded.
I called auto electrician plug into scanner and he said it was showing permanent faults in ECU including cooling fan fault, EGR fault and other faults which he deleted.
He aslo said a wire from top of diesel pump my be a bypass wire for the immobiliser. Also there has been a press button fitted on dash I presume to bypass heater plug relay.
Now after auto elc. has gone I have a permanent diesel knock and loss of power, no temp gauge working which is now making van overheat as well as all other faults!!
I do like a challenge but it's obvious someone else has messed with this van and would be grateful for any advice. It is a shame cos van drives really nice when running ok!!

Thanks again for any info
Chaz

It could be some bad connections some where, If you could P/Mail me your Vin No. I'll have a look at the correct drawings.Icon_thumright

hi again. vin no from inner wing is. 0VF7GBWJYB94012211O.
Reply
#2
Don't quote me but to me you have a few faults that might not be related to each other.
Do the basics, check main earths - engine and chassis. Check the battery is charged up and no loose connections.
As the engine will run then fault check the condition of the engine speed sensor (No.7 in diagram) and connections, this is essential for the injection.
Change fuel filter.
Also check these earth points
MC42 - for speedo unit
MC56 - for com2000 unit
MC13 & MC11 - for Bsi and engine fuse box module.
MC20 - head lights.
Do you have a multimeter?

.pdf   DW8B flywheel sensor.pdf (Size: 69.55 KB / Downloads: 30)
   
2006 2.0hdi 600 with bench seat.  Cool
Reply
#3
(07-04-2013, 09:43 AM)Rustscrat Wrote:  Don't quote me but to me you have a few faults that might not be related to each other.
Do the basics, check main earths - engine and chassis. Check the battery is charged up and no loose connections.
As the engine will run then fault check the condition of the engine speed sensor (No.7 in diagram) and connections, this is essential for the injection.
Change fuel filter.
Also check these earth points
MC42 - for speedo unit
MC56 - for com2000 unit
MC13 & MC11 - for Bsi and engine fuse box module.
MC20 - head lights.
Do you have a multimeter?

thanks, Will check on monday.dont have a m/m but will check earths first.
Reply
#4
Hi again, thanks Rustcrat for diagram. Chased all earth points in large diagram, removed and cleaned themapart from EMO3L which I presume is wiper motor earth.
But small diagram in box E, I can't figure out where on the van that is! Any idea??
I have also found a second hand heater plug relay - thus trying to eliminate the extra wiring. But still showing no heater plugs light on dash.
Speed senser looks clean.
Once again thanks for your input
Chazy
Reply
#5
It's the driver's side cab floor; look on the right and you'll see the door jamb - transmission tunnel is on your left.
[+] 2 users say Thank You to addo for this post
Reply
#6
Ihave decided to risk buying a second hand bsi ecu and key,
cant find any wiring faults.Will post results.
[+] 1 user says Thank You to chazy for this post
Reply
#7
(14-04-2013, 07:14 PM)chazy Wrote:  Ihave decided to risk buying a second hand bsi ecu and key,
cant find any wiring faults.Will post results.

Hi, I have a 2004 1.9d enterprise van model, with the exact same problem, bought a new comms 2000 unit and fitted with no change, still no lights etc, have also tried bsi  reset with no luck, may I ask did changing the bsi, Ecu and key solve your problem, many thanks Richard
Reply
#8
Rick you are most unlikely to get a reply since chazy is no longer using the forum .... look at his details below ..

chazy's Forum Info
Joined: 05-04-2013
Last Visit: 18-05-2013, 08:54 PM
[+] 1 user says Thank You to geoff for this post
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Search Forums

(Advanced Search)

Latest Threads
increase in a ratchet-typ...
Last Post:saskak
Today 12:36 AM
» Replies: 7
» Views: 101
DW8 engine tapping
Last Post:Hector Scorn
Today 12:30 AM
» Replies: 0
» Views: 5
Rear Wiper Motor
Last Post:madwelshman
Yesterday 10:42 PM
» Replies: 3
» Views: 113
Heater control unit/resis...
Last Post:mreid63
Yesterday 10:34 PM
» Replies: 5
» Views: 336
Loud beeping from radio u...
Last Post:Tonyash
Yesterday 10:13 PM
» Replies: 0
» Views: 22
Facial light replacement
Last Post:Mike
Yesterday 09:23 PM
» Replies: 11
» Views: 288
Reverse light switch prob...
Last Post:willpisme
Yesterday 08:09 PM
» Replies: 7
» Views: 158
Rear hub nut torque setti...
Last Post:geoff
Yesterday 07:31 PM
» Replies: 4
» Views: 88
Heyup
Last Post:polar
Yesterday 07:18 PM
» Replies: 9
» Views: 372
New owner
Last Post:SheilaAnn
Yesterday 04:33 PM
» Replies: 12
» Views: 585

Locations of visitors to this page