Thread Rating:
  • 4 Vote(s) - 3.5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Mk2 Rear Wiper internals
#1
Hi all, just stripped down the rear wiper assembly on my Mk2 Multispace and thought someone may benefit from the pictures I took of the inside bits.

Obviously the plastic trim panel needs to be removed first. Two torx screws need to be removed from under the plastic strip on the handle. The panel will then pull off. Make sure you don't lose any of the plastic clips.

Remove the nut holding the wiper. I needed a puller to get the wiper off its shaft. The motor assembly is held on by 3 rivots. Drill these out. Remove the washer pipe and disconnect the electrical connector.

On the bench remove the plastic tube that fits inside the shaft. This carries the water for the washer jet and is probably what leads to most of the problems with the rear wiper assembly.

Remove the small torx bolts and carefully separate the plastic cover from the metal body. The brushes for the motor are on the plastic part and the motor itself is on the metal part.

The motor turns a screw which engages with the large plastic wheel. As this turns, the metal linkage rotates and eventually turns the shaft. I found I could turn the motor using a finger on the commutator, but there was a position where it was very stiff. The shaft on mine was sticking, so I took it out of the tube and cleaned it up. Tried again and it was free to turn all the way round.

On reassembly make sure the brushes fit to the motor correctly.

   
   
   
[+] 5 users say Thank You to Modmytop for this post
Reply
#2
Are they standard pop rivets?Confusedcratch:
Strawberry flavoured windows  Dodgy
Reply
#3
You need one of these:
http://www.ebay.co.uk/itm/Lazy-Tong-Tong...4897.l4276

and 3 pop rivets they are either 6mm or 6.4mm can't remember.

or

http://www.ebay.co.uk/itm/PROFESSIONAL-4...0463087894

then use bolts to secure it in place

Or
I bought the 3 rivets & took them down to my local garage who fitted them in 2 mins for £5

regards

Tony
[+] 2 users say Thank You to tc_1 for this post
Reply
#4
Only today and from that advert, did I learn those riveters work on a pull, not a push! A clear demonstration of the type of fringe detail you miss out upon, when self taught in mechanicals.

Any ideas where the "lazy tong" name originated? Is it because of the extendable grips they resemble?
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.


  

Password
  





Search Forums

(Advanced Search)

Latest Threads
Ncb help
Last Post:Silverberlingo
Today 10:26 PM
» Replies: 4
» Views: 139
Saying Hello
Last Post:Jed Clampit
Today 10:25 PM
» Replies: 1
» Views: 19
1.6 hdi 90bhp Turbo and i...
Last Post:Floydster
Today 07:48 PM
» Replies: 3
» Views: 135
1.6 16v petrol cambelt
Last Post:sks01773
Today 07:37 PM
» Replies: 12
» Views: 250
Heated wing mirrors
Last Post:Trevor
Today 07:06 PM
» Replies: 3
» Views: 82
2025 Diesel Ban
Last Post:Tree
Today 06:17 PM
» Replies: 15
» Views: 345
Hello
Last Post:Johny555
Today 06:04 PM
» Replies: 1
» Views: 19
Roof noise
Last Post:Veitcast
Today 05:48 PM
» Replies: 0
» Views: 28
Fuel consumption
Last Post:Opensauce
Today 05:37 PM
» Replies: 3
» Views: 53
Lexia clone that works wi...
Last Post:kennard
Today 02:59 PM
» Replies: 58
» Views: 1840

Locations of visitors to this page