Thread Rating:
  • 3 Vote(s) - 1.33 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Adjust Side Mirrors
Hello to all, I've recently bought a 110XTR late 2009.

When trying to adjust the drivers side mirror (UK right hand drive, only electric adjustment), I cannot adjust it very far outwards, I can still see the side of the Berlingo. However turning it inwards I can see myself. It's as if the starting point is too far in.

Is this a fault?

Thanks and love the car.
Not so much a fault as a production cost saving omission. Citroen have not 'right hand drived' the mirrors. ie they are set up for left hand drive.
Thanks, would the UK allow vehicles to be allowed on the road with a spec which isn't fit for purpose, would a rear mirror that didn't face the rear be allowed.
I wonder if the glass in your mirror has been replaced at some time and not properly seated? Mine shows the offside quiet clearly. Be careful if you try to remove/replace the glass it needs caution not to crack it.

2012 Iron Grey XTR 110 with lots of bits and bobs.
Tbf, I don't find it much of a problem & I'm guessing it is still within UK spec but I noticed this myself & guessed the reason. If you sit in the front passenger seat you will notice the mirrors can adjust perfectly. Its possible the mirrors have been rhd'ed on later mk3s.
Spoke to the after sales people, got to ring them back to let them know if the whole of the mirror was correctly unfolded and seated, it is.

He asked if I can get it to them tomorrow for a check.
They adjusted the drive as far as it would go, so slightly better but not ideal.

I might take a trip to a Citroen dealer and sit in one and try adjusting the mirror.
Citroen mechanic had a quick look and said its ok in terms of the operation and agreed it maybe as Opensauce says "set up for left hand drive".

Trevor, do you not have a large blind spot on there off side?

This is not a solution but I have fitted 2 blind spot mirrors to my Berlingo.It helps a lot on motorway junctions etc.Confusedalut:
Strawberry flavoured windows  Dodgy
I bet you could oversize the motor module fixing holes and shim it slightly.
[+] 1 user says Thank You to addo for this post

Forum Jump:

Users browsing this thread: 1 Guest(s)
Welcome, Guest
You have to register before you can post on our site.



Search Forums

(Advanced Search)

Latest Threads
Newbie checking in
Last Post:Johny555
Today 01:57 PM
» Replies: 1
» Views: 14
I'm hearing better or smt...
Last Post:andy-M
Today 01:40 PM
» Replies: 9
» Views: 327
M49 1.9 diesel misfire a...
Last Post:ricc
Today 01:14 PM
» Replies: 6
» Views: 144
Eco activated but engine ...
Last Post:doofer
Today 01:05 PM
» Replies: 25
» Views: 762
Bump and Run - Am I right...
Last Post:doofer
Today 01:00 PM
» Replies: 16
» Views: 242
replacing diesel fuel pip...
Last Post:Col
Today 10:30 AM
» Replies: 36
» Views: 2052
Dead BSI unit?
Last Post:ghost123uk
Today 09:03 AM
» Replies: 5
» Views: 143
Injectors and B9 series.....
Last Post:Opensauce
Today 06:55 AM
» Replies: 1
» Views: 62
2004 2.0HDi Cruise Contro...
Last Post:brajomobil
Today 06:29 AM
» Replies: 1
» Views: 63
Radio not working and ele...
Last Post:pscotty
Today 04:02 AM
» Replies: 0
» Views: 32

Locations of visitors to this page